Lacing a corset isn't hard, but it is a technique, and almost every "corsets hurt" story starts with lacing done wrong: pulled tight all at once, tightened only from the bottom, or forced closed in one go. This is the method Heidi uses on every corset she owns, including the one in her "Yes I can lace my corset by myself" video.
Before You Start: Know Your Corset
A corset with steel boning closes in two places. The busk is the front closure: two steel strips with loops on one side and pins on the other. The lacing runs through the eyelets (grommets) at the back and does the actual shaping. You never tighten or loosen with the busk. The busk only opens and closes; all adjustment happens at the back.
You'll need the corset, a long lace (most corsets need 5–8 yards; it's better to have too much than too little), and ideally a mirror, or two mirrors so you can see your back.
Step 1: Lace It Correctly Before You Put It On
The standard method is "bunny-ear" lacing. It lets you pull the whole back tight from the waist instead of from the ends.
- Start at the top. Find the middle of the lace and thread both ends down through the top pair of eyelets from the outside, so the lace makes a straight bar across the top.
- Criss-cross downward. Cross the lace ends and thread them through the next pair of eyelets, always going in from the same side (outside to inside, or inside to outside; just be consistent). Continue until you reach the waistline, the narrowest point of the corset.
- Make the bunny ears. At the waistline, don't cross. Instead, run each lace straight down into the eyelet directly below on the same side, leaving a long loop of 12–18 inches sticking out on each side. These two loops are the "bunny ears," and they are what you'll pull to tighten.
- Finish to the bottom. Keep criss-crossing below the ears to the bottom pair of eyelets, and tie the ends together at the bottom with a bow you can undo later.
Now loosen the whole back generously, at least 4–6 inches open, before you put the corset on. A corset that starts too tight can't be closed at the busk without straining the steels.
Step 2: Put It On and Close the Busk
Wear a thin, snug layer underneath (a tank top, chemise or corset liner). It protects the corset from skin oils and protects your skin from the seams.
Wrap the corset around you with the lacing at your back. Close the busk from the middle outward: hook the pins at your waist first, then work up and down. If the busk won't close, the lacing is still too tight; loosen it more rather than forcing the pins.
Step 3: Tighten in Rounds, Not All at Once
- Take up the slack from the top down. Starting at the top, pull each crossed section of lace snug toward the waist, working down to the bunny ears. Then do the same from the bottom up toward the waist. All the slack should end up in the two bunny ears.
- Pull the bunny ears out to the sides. Hold one loop in each hand and pull outward, away from your body (not backward). The corset tightens evenly around the waist.
- Stop and breathe. Tighten until it's snug, not tight. Then walk around for a few minutes. Your body warms up and settles into the corset.
- Repeat the round. Take up the new slack from top and bottom into the ears again, pull, and pause. Two or three rounds over 10–15 minutes gives a much better and more comfortable result than one hard pull.
Tie off the bunny ears in a bow at the waist and tuck the loops under the lacing or into the bottom of the corset so they don't dangle.
Lacing Yourself With No Helper
Heidi laces herself in daily, and it takes her about 15 minutes. The trick is that bunny-ear lacing puts the pulling point at your waist, which is easy to reach behind you.
- Lace it loosely, step in and close the busk as above.
- Work by feel and with a mirror. Reach behind you with both hands and pull the slack toward the waist in sections, a few crosses at a time. A second mirror behind you helps you check that the gap is even.
- Use a doorknob or hook as an anchor if your arms tire. Loop the ears over a sturdy doorknob, step forward gently, and the lace tightens evenly. Go slowly.
- Accept that your arms will be tired. It's a workout the first few times. A helper makes it faster (Heidi calls hers a "lacing assistant"), but you don't need one.
What the Back Should Look Like
When you're done, the gap at the back should be parallel: about the same width at the top, waist and bottom. A gap of 1–3 inches is normal and fine. If the gap is a "V" (wider at the top or bottom) or an "A" shape, or if the boning near the gap is bending, the corset doesn't match your shape there, or you've pulled one section much harder than the others. Loosen and redo the round.
Taking It Off
Loosen the bunny ears and pull slack back up and down the lacing until the back is open a few inches. Then open the busk from the top and bottom toward the middle. Never pop a busk open while the lacing is still tight; it strains the steels and the fabric around the pins.
Frequently Asked Questions
From the waist. With bunny-ear lacing, slack is pulled from the top down and from the bottom up into the loops at the waistline, so the waist tightens evenly without crushing the ribs or hips.
About 10–15 minutes once you're practiced, including two or three tightening rounds. The first few times take longer.
Most full corsets need 5–8 yards of lacing. Too long is easy to tuck away; too short won't let the back open enough to close the busk.
Yes. A parallel gap of about 1–3 inches is normal for most corsets. What matters is that the gap is even from top to bottom.
Keep going with Heidi
Short, practical videos on corsets, gowns and cosplay construction.
Subscribe on YouTubeJoin Heidi's Patreon as a free member to get new guides, build updates and behind-the-scenes posts by email. No payment needed.
Join free on PatreonFull photosets, build documentation and behind-the-scenes from the sewing studio for members, from $6/month.
See the full sets on Patreon